LC sizing, coil former calculation (Nagaoka / Rosa) and STL export for 3D printing — for multiband trapped antennas.
LC Resonant Circuit Principle
An antenna trap is an LC circuit (inductor + capacitor) connected in parallel and inserted in series in the radiating element of a multiband antenna.
At its resonant frequency f₀, the impedance of the LC circuit becomes very high (theoretically infinite) — this blocks HF current and electrically isolates the antenna section beyond the trap. The antenna then behaves like a shortened dipole, tuned to the highest band.
On lower bands, the trap is no longer at resonance and acts as a series inductor, electrically shortening the antenna and compensating for the missing physical length.
Resonance Formula
f₀ = 1 / (2π × √(L × C))
f₀ in Hz · L in H · C in F
C = 1 / ((2πf₀)² × L)
L = 1 / ((2πf₀)² × C)
Schematic — Parallel LC Circuit
Building a Coaxial Trap
In a coaxial trap, the coaxial cable acts as both the inductor and the capacitor. There are no separate discrete components.
- Inductance (L) — created by winding the coaxial cable (N turns) around a cylindrical former (PVC tube, nylon, 3D print).
- Capacitance (C) — distributed capacitance between the centre conductor and the braid. C = cable length × linear capacitance (pF/m, specific to the chosen cable).
The circuit is closed by one single link: the centre conductor of one end soldered to the braid of the other end. The remaining free braid and free centre conductor are the two trap terminals.
Nagaoka Formula (coaxial coil)
L = µ₀ × N² × A × Kn / ℓ
Kn = exact Nagaoka coefficient (complete elliptic integrals), function of D/ℓ: 0.82 (D/ℓ = 0.5) · 0.69 (1) · 0.53 (2) · 0.20 (10)
D = former Ø + cable Ø (mean turn diameter) · A = π×(D/2)² · ℓ = N × pitch · µ₀ = 4π×10⁻⁷ H/m
N and ℓ (winding length) are solved simultaneously with C to resonate at f₀.
Construction — Coaxial Trap on Former
Application: 80/40 m Multiband Dipole
80/40 m Trapped Dipole — Overview
On 40 m (trap resonance f₀)
The traps resonate and present a very high impedance. Current stops at the traps — the antenna behaves as a half-wave dipole on 40 m, without using the outer wire sections.
On 80 m (below f₀)
The traps are no longer at resonance and act as series inductors loading the outer wire sections. The total length (including outer sections) resonates on 80 m, with a slightly shortened antenna compared to a full-size dipole.
Discrete Coil or Coaxial Trap — Which to Choose?
Coaxial Trap Recommended
The coaxial cable acts as both the coil and the capacitor — no discrete components are exposed to the weather. This is the near-universal solution for permanent outdoor HF antennas.
- Robust, weatherproof, UV and moisture resistant
- Easy to build with common materials (RG-58, RG-213…)
- Power rating set by the cable's voltage withstand (see module 1)
- No discrete capacitor exposed to the weather
- Lower Q than a carefully built discrete coil (negligible impact in practice for most antennas)
Discrete Coil + Capacitor
Enamelled wire coil wound on a support, ceramic or silver mica capacitor in parallel. Used in specific contexts where a high Q or maximum compactness is required.
- Potentially higher Q → better band selectivity
- Fine f₀ adjustment possible with a trimmer capacitor
- Can be very compact for QRP portable antennas
- Discrete capacitor vulnerable to moisture and arcing (high power)
- Requires careful encapsulation for permanent outdoor use
In amateur radio practice, the coaxial trap is the default choice in this tool and covers the vast majority of needs. The discrete coil remains available for special cases (lab, contest, QRP portable). Both modes use formulas suited to their geometry: Nagaoka for coaxial traps, Wheeler for discrete coils.
Construction Procedure (Coaxial Trap)
Build two identical traps for a dipole (one per side). Test them individually before installing. Calculated values are theoretical estimates — final adjustment with an LCR meter or antenna analyser is essential in practice.
1. Trap LC Calculator
Custom cable — enter the linear capacitance directly, or the impedance and dielectric constant if you prefer to start from those values (automatic calculation).
Formula: f = 1 / (2π√(LC)). Theoretical estimate — validate/adjust in practice with an LCR meter and SWR meter.
Trap Power Rating
η depends on the antenna and on how far f₀ is from the operating frequency: it cannot be computed here. The reference values come from W8JI's published EZNEC analyses (total loss of both traps in a trapped dipole).
▶ Second case: trap used as a loading coil on a lower band
Below its resonance the trap is no longer a rejector but a loading coil carrying the antenna current, amplified by 1/(1−(f/f₀)²) inside the coil. The current through it is bounded by the feed-point current √(P/R); factor k scales it to the trap's actual position (k = 1: worst case, trap at the current maximum). In practice the trap sits further out along the element and k is well below 1: cross-checking against the 0.05 dB loss W8JI publishes on 80 m puts k around 0.35–0.45, but that figure depends on the exact geometry and on assumptions about X and Q — determine it by NEC modelling. Q is assumed constant with frequency (it actually rises roughly as √f). The power shown assumes a 100 % duty cycle.
Model, at resonance: Rp = Q·XL, Vrms = √(Rp × η × PPEP), I = Vrms/XL. Limits: PPEP = Vmax²/(Rp × η) for voltage, PPEP = Imax² × XL/(Q × η × d) for heating, with Imax = 3.5 A/mm² of copper (enamelled wire in free air, usual range 2.5–6) and d the average-to-PEP duty cycle: 40 % CW, 20 % SSB without processing (40 % with heavy processing), 100 % digital and FM — ARRL "RF Exposure and You", worksheet B.
2. Former Sizing (Nagaoka / Rosa)
| N turns | Alignment | Ø former | PVC standard | Offset | Winding length | Cable/wire length |
|---|
Same side: integer N — cable entry and exit emerge from the same side of the former. 180°: N + ½ turn — entry and exit on opposite sides. Click a row to apply.
Formule de Wheeler : L(µH) = (D² × N²) / (18D + 40ℓ), D et ℓ en pouces. Calcul itératif sur N. Theoretical estimate — manufacturing tolerance ±5–10%, final adjustment with LCR meter.
3. STL Export for 3D Printing
Recommended material: PETG for a trap intended for permanent outdoor use (better UV and heat resistance). PLA is acceptable for portable use or a temporary test prototype, but deforms under direct sunlight.
The parametric former is generated directly in the browser (triangulated mesh, no external dependency). The guide groove is obtained by local radial deformation of the tube along a true helical path, sized to the effective diameter entered in module 2 — winding wire in discrete coil mode, or the outer diameter of the selected coaxial cable (synchronised automatically) in coaxial trap mode. Pitch and groove depth adjust accordingly; adjust for your printer's tolerance.
4. Assembly Diagram
The diagram updates automatically with the calculated parameters.
